4.3.2.1 · 相关附加要求
42-24 · 来源 PDF 页码 391
COPRA
| UN 编号 | UN1363 |
|---|---|
| 中文名称 | 干椰子肉 |
| 英文名称 | COPRA |
| 危险类别 | 第4.2类 |
| 包装类别 | III |
| 海洋污染物 | 原表未标注;须结合实际货物分类核对 |
| 有限数量 | 0 |
| 例外数量 | E0 |
| EmS 应急措施 | F-A, S-J |
带有渗透性的陈腐脂肪臭味的 椰子干仁,其气味可污染其他 货物。
Dried kernels of coconuts, with a penetrating rancid odour which may taint other cargoes.
出处:IMDG Code 42-24 第 627 页
当前条目 1 列明的包装导则: P003、LP02 ;有限数量 0,例外数量 E0。
核对英文原文页面与脚注 ↗ · 官方 PDF 169–169
P003 危险货物须置于合适的外包装中。内包装须符合第 4.1.1.1、4.1.1.2、4.1.1.4、4.1.1.8 条和第4.1.3节的规定,其设计须符合第6.1.4节的构造规定。须使用由合适材料制成的外包装, 其强度和设计须与包装容量和预期用途相称。当本导则规则用于物品或组合包装内容器的运输时,包装的的设计和构造须防止物品在正常运输条件下意外筛漏。 特殊包装规定: PP16 对于UN 2800,须防止电池在包装内短路。 PP17 对于 UN 2037,纤维板包装的包件的净重不得超过 55 kg,其他包装的包件净重不得超过125 kg。 PP18 对于 UN 1845,包装的设计和构造须允许释放二氧化碳气体,以防止压力积聚导致包装破裂。 PP19 对于UN 1327、1364、1365、1856和3360,允许以捆包形式运输。 PP20 对于UN 1363、1386、1408、2793,可以使用任何防筛漏、防撕裂容器。 PP32 对于 UN 2857、3358 以及根据 UN 3164托运的坚固物品,可以不包装,装在板条箱或适当的外包装中运输。 注:批准的包装净重可超过 400 千克(见第4.1.3.3条)。 PP90 对于 UN 3506 和 3354,须使用密封的内衬或袋子,内衬和袋子由坚固的防漏、防刺穿材料制成,这些材料不透汞或镓,视情而定,无论包装处于何种位置,都能防止物质从包件中漏出。 PP91 对于 UN1044,大型灭火器也可无包装运输,但前提是满足第 4.1.3.8.1.1 至 4.1.3.8.1.5条的规定,阀门采用第 4.1.6.1.8.1至 4.1.6.1.8.4中规定的任一方法进行防护,且安装在灭火器上的其他设备受到保护,以防止意外启动。就本特殊包装规定而言,“大型灭火器”系指第3.3章特殊规定225第.3至.5款中描述的灭火器。 PP96 对于根据特殊规定327运输的UN 2037废气罐,包装须充分通风,以防止产生危险气氛和压力积聚。 PP100 对于 UN1408 和 2793,柔性、纤维板或木质包装须防筛漏和防水,或须装有防筛漏和防水衬里。
P003 Dangerous goods shall be placed in suitable outer packagings. The packagings shall meet the provisions of 4.1.1.1, 4.1.1.2, 4.1.1.4, 4.1.1.8 and 4.1.3 and be so designed that they meet the construction provisions of 6.1.4. Outer packagings constructed of suitable material, and of adequate strength and design in relation to the packaging capacity and its intended use, shall be used. Where this packing instruction is used for the transport of articles or inner packagings of combination packagings, the packaging shall be designed and constructed to prevent inadvertent discharge of articles during normal conditions of transport. Special packing provisions: PP16 For UN 2800, batteries shall be protected from short circuit within the packagings. PP17 For UN 2037, packages shall not exceed 55 kg net mass for fibreboard packagings or 125 kg net mass for other packagings. PP18 For UN 1845, packagings shall be designed and constructed to permit the release of carbon dioxide gas to prevent a build-up of pressure that could rupture the packagings. PP19 For UN Nos. 1327, 1364, 1365, 1856 and 3360, transport as bales is authorized. PP20 For UN Nos. 1363, 1386, 1408 and 2793, any sift-proof, tearproof receptacle may be used. PP32 UN Nos. 2857 and 3358 and robust articles consigned under UN 3164 may be transported unpackaged, in crates or in appropriate overpacks. Note: The packagings authorized may exceed a net mass of 400 kg (see 4.1.3.3). PP90 For UN Nos. 3506 and 3554, sealed inner liners or bags of strong leakproof and puncture resistant material impervious to mercury or gallium, as appropriate, which will prevent escape of the substance from the package irrespective of the position of the package shall be used. PP91 For UN 1044, large fire extinguishers may also be transported unpackaged provided that the requirements of 4.1.3.8.1.1 to 4.1.3.8.1.5 are met, the valves are protected by one of the methods in accordance with 4.1.6.1.8.1 to 4.1.6.1.8.4 and other equipment mounted on the fire extinguisher is protected to prevent accidental activation. For the purpose of this special packing provision, “large fire extinguishers” means fire extinguishers as described in subparagraphs.3 to.5 of special provision 225 of chapter 3.3. PP96 For UN 2037 waste gas cartridges transported in accordance with special provision 327, the packagings shall be adequately ventilated to prevent the creation of dangerous atmospheres and the build-up of pressure. PP100 For UN Nos. 1408 and 2793 flexible, fibreboard or wooden packagings shall be sift-proof and water-resistant or shall be fitted with a sift-proof and water-resistant liner.
只要符合第 4.1.1 和 4.1.3 节的一般规定,允许使用下列大型包装:
按当前一览表条目列明的导则与包装类别核对。内包装限量和外包装限量须同时满足,并结合该条目列明的特殊包装规定。
| 包装类型 / 代码 | 包装类 I | 包装类 II | 包装类 III |
|---|---|---|---|
| 钢50A | 不允许 | 不允许 | 3 m³ |
| 铝50B | 不允许 | 不允许 | 3 m³ |
| 钢和铝以外的金属50N | 不允许 | 不允许 | 3 m³ |
| 硬质塑料50H | 不允许 | 不允许 | 3 m³ |
| 天然木50C | 不允许 | 不允许 | 3 m³ |
| 胶合板50D | 不允许 | 不允许 | 3 m³ |
| 再生木50F | 不允许 | 不允许 | 3 m³ |
| 硬质纤维板50G | 不允许 | 不允许 | 3 m³ |
| 软质塑料c51H | 不允许 | 不允许 | 3 m³ |
请按当前一览表条目核对适用代码,不代表以下规定全部适用于本票货物。
L2 删除
L3 对于 UN 1309、1376、1483、1869、2793、2858 和 2878,软质或纤维板内包装须 防筛漏、防水,或须装有防筛漏、防水的衬里。
L4 对于 UN 1932、2008、2009、2545、2546、2881 和 3189,软质或纤维板内包装须 密封。
IMDG 42-24 · 来源 PDF 页码:336, 337
(固体) LP02 只要符合第4.1.1和4.1.3节的一般规定,允许使用下列大型包装: 玻璃 10kg 钢(50A) 塑料b 50kg 铝(50B) 不允许不允许 3mc 金属 50kg 除钢和铝的其他金属纸a,b 50kg (50N) 纤维a,b 50kg 硬质塑料(50H) (固体) LP02 天然木(50C) 胶合板(50D) 再生木(50F) 硬质纤维板(50G) 软质塑料(51H)c a 当运输的物质在运输过程中可能变成液体时,不得使用这些包装。 b 包装须防筛漏。 c 仅与软质内包装一起使用。 特殊包装规定: L2 删除 L3 对于UN 1309、1376、1483、1869、2793、2858和2878,软质或纤维板内包装须防筛漏、防水,或须装有防筛漏、防水的衬里。 L4 对于UN 1932、2008、2009、2545、2546、2881和3189,软质或纤维板内包装须密封。
(SOLIDS) LP02 The following large packagings are authorized, provided the general provisions of 4.1.1 and 4.1.3 are met. Inner packagings Large outer packagings Packing group I Packing group II Packing group III 4 Glass 10 kg Steel (50A) Plasticsb 50 kg Aluminium (50B) Not allowed Not allowed 3 m3 Metal 50 kg Metal other than steel or Papera, b 50 kg aluminium (50N) Fibrea, b 50 kg Rigid plastics (50H) Natural wood (50C) Plywood (50D) Reconstituted wood (50F) Rigid fibreboard (50G) Flexible plastics (51H)c a These packagings shall not be used when the substances being transported may become liquid during transport. b Packagings shall be sift-proof. c To be used with flexible inner packagings only. Special packing provision: L2 Deleted L3 For UN Nos.1309, 1376, 1483, 1869, 2793, 2858 and 2878, flexible or fibre inner packagings shall be sift-proof and water-resistant or shall be fitted with a sift-proof and water-resistant liner. L4 For UN Nos.1932, 2008, 2009, 2545, 2546, 2881 and 3189 flexible or fibre inner packagings shall be hermetically sealed.
所属导则:P003
核对英文原文页面与脚注 ↗ · 官方 PDF 169–169
对于UN 1363、1386、1408、2793,可以使用任何防筛漏、防撕裂容器。
For UN Nos. 1363, 1386, 1408 and 2793, any sift-proof, tearproof receptacle may be used.
IBC08 只要符合第4.1.1、4.1.2和4.1.3节的一般规定,允许使用下列IBCs: 金属(11A、11B、11N、21A、21B、21N、31A、31B 和 31N); 硬质塑料(11H1、11H2、21H1、21H2、31H1 和 31H2); 复合包装(11HZ1、11HZ2、21HZ1、21HZ2 和 31HZ1); 纤维板(11G); 木质包装(11C、11D和11F); 软质包装(13H1、13H2、13H3、13H4、13H5、13L1、13L2、13L3、13L4、13M1 IBC08 或13M2)。 补充规定: 如果在运输期间固体变成液体,请参见第4.1.3.4条。 特殊包装规定: B3 软质IBCs须防筛漏和防水,或装配防筛漏和防水内衬。 B4 软质、纤维板或木制IBCs须防筛漏和防水,或配备防筛漏和防水内衬。 B6 对于 UN 1327、1363、1364、1365、1386、1408、1841、2211、2217、2793 和 3314的IBCs,无需满足第6.5章的IBCs试验要求。 B21 除了金属或硬质塑料 IBCs,对于盛装固体物质的 IBCs 须装在封闭货物运输组件或货运集装箱/货运车辆内运输,货物运输组件或货运集装箱/货运车辆须具有至少与IBCs高度相同的硬质侧壁或围栏。
IBC08 The following IBCs are authorized, provided the general provisions of 4.1.1, 4.1.2 and 4.1.3 are met: Metal (11A, 11B, 11N, 21A, 21B, 21N, 31A, 31B and 31N); Rigid plastics (11H1, 11H2, 21H1, 21H2, 31H1 and 31H2); Composite (11HZ1, 11HZ2, 21HZ1, 21HZ2 and 31HZ1); Fibreboard (11G); Wooden (11C, 11D and 11F); Flexible (13H1, 13H2, 13H3, 13H4, 13H5, 13L1, 13L2, 13L3, 13L4, 13M1 or 13M2). Additional provisions: Where the solid may become liquid during transport see 4.1.3.4. Special packing provisions: B3 Flexible IBCs shall be sift-proof and water-resistant or shall be fitted with a sift-proof and water-resistant liner. B4 Flexible, fibreboard or wooden IBCs shall be sift-proof and water-resistant or shall be fitted with a sift-proof and water-resistant liner. B6 For UN Nos. 1327, 1363, 1364, 1365, 1386, 1408, 1841, 2211, 2217, 2793 and 3314, IBCs are not required to meet the IBC testing provisions of chapter 6.5. B21 For solid substances in IBCs other than metal or rigid plastics IBCs, the IBCs shall be carried in closed cargo transport units or in freight containers/vehicles, which shall have rigid sides or fences at least to the height of the IBC.
所属导则:IBC08
核对英文原文页面与脚注 ↗ · 官方 PDF 232–232
软质IBCs须防筛漏和防水,或装配防筛漏和防水内衬。
Flexible IBCs shall be sift-proof and water-resistant or shall be fitted with a sift-proof and water-resistant liner.
所属导则:IBC08
核对英文原文页面与脚注 ↗ · 官方 PDF 232–232
对于 UN 1327、1363、1364、1365、1386、1408、1841、2211、2217、2793 和 3314的IBCs,无需满足第6.5章的IBCs试验要求。
For UN Nos. 1327, 1363, 1364, 1365, 1386, 1408, 1841, 2211, 2217, 2793 and 3314, IBCs are not required to meet the IBC testing provisions of chapter 6.5.
一览表未列明可移动罐柜 T 导则。其他适用条款仍须核对;BK 散装容器要求如有列明,会单独显示。
BK 是散装容器代码,与可移动罐柜 T 导则不同。列有代码不代表本票货物已满足海运条件;须结合适用一览表条目、第 4.3 章及第 6.9 章容器要求核对。
42-24 · 来源 PDF 页码 391
注: 除满足第 4.3.3 节要求外,帘布式散装容器(BK1)不得用于海运。
42-24 · PDF 389
42-24 · PDF 389
42-24 · PDF 389
42-24 · PDF 389
42-24 · PDF 389
42-24 · PDF 389
42-24 · PDF 389
42-24 · PDF 390
42-24 · PDF 390
42-24 · PDF 390
42-24 · PDF 390
42-24 · PDF 390
42-24 · PDF 390
42-24 · PDF 390
42-24 · PDF 390, 391
42-24 · PDF 391
42-24 · PDF 391
42-24 · PDF 391
条目 1 的包件标签与标记预览。请结合实际货物分类及特殊规定核对。
4.2当前条目 1 列明的特殊规定: 29、926、973。
核对英文原文页面与脚注 ↗ · 官方 PDF 753–753
包装,包括大捆,可免贴标志,但须标上适当的类别(例如“第4.2类”)。
The packages, including bales, are exempt from labelling provided that they are marked with the appropriate class (e.g. “class 4.2”).
核对英文原文页面与脚注 ↗ · 官方 PDF 781–781
该物质在装运前须最好风干不少于一个月,除非托运人所载国主管当局认可的证明,声明其最大含水量为5%。
This substance shall preferably have been weathered for not less than one month before shipment unless a certificate from a person recognized by the competent authority of the country of shipment states a maximum moisture content of 5%.
除大包外,包件还须根据第5.2.1节显示其所载物质的正确运输名称和联合国编号。在任何情况下,如果包件(包括捆包)装在货物运输组件中,且其中包含的货物只分配了一个联合国编号,则这些包件可以免贴类别标志。装载包件(包括捆包)的货物运输组件须根据第 5.3 章显示任何相关标签、标牌和标记。
Packages, with the exception of bales, shall also display the proper shipping name and the UN number of the substance that they contain in accordance with 5.2.1. In any case, the packages, including bales, are exempt from class marking provided that they are loaded in a cargo transport unit and that they contain goods to which only one UN number has been assigned. The cargo transport units in which the packages, including bales, are loaded shall display any relevant labels, placards and marks in accordance with chapter 5.3.
| 积载与操作 | 积载类A SW1 SW9 H1(Category A SW1 SW9 H1) |
|---|---|
| 隔离 | 一览表未列明隔离要求 |
对袋装货物提供良好的全面通风,建议用双条积载,第7.6.2.7.2.3条给出了怎样达到此种积载方式。货物应”远离”容易受热的管道和舱壁 (如机舱或加热的燃油柜舱壁)。在航行期间,须定时在货舱不同深度测量温度并记录读数。如果货物温度超过环境温度并继续上升,须关闭通风。
Provide a good through ventilation for bagged cargo. Double strip stowage is recommended. The illustration in 7.6.2.7.2.3 shows how this can be achieved. During the voyage regular temperature readings shall be taken at varying depths in the hold and recorded. If the temperature of the cargo exceeds the ambient temperature and continues to increase, ventilation shall be closed down.
出口危险货物包装使用鉴定结果单(危包证)的办理逻辑,以及它和船级社证、钢瓶证、SOC 罐证分别在什么场景下用、向谁申请。
按IMDG42-24逐项核对DG申请表,区分规则必需内容和承运人补充字段,处理无包装组、条件性副危险和LQ等情况。
打开 UN1363 的交互查询,核对类别、包装与隔离要求。DG 表生成暂未开放使用。
打开规则查询 →